(navigation image)
Home American Libraries | Canadian Libraries | Universal Library | Community Texts | Project Gutenberg | Children's Library | Biodiversity Heritage Library | Additional Collections
Search: Advanced Search
Anonymous User (login or join us)
Upload
See other formats

Full text of "Tools"

The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Make] Projects 

hhiiilH ho/ 1 !/ tuMaal/ chare r\icf*f\\tat* 



build, hack, tweak, share, discover,- 



The MakerGear Mosaic 3D 



Printer - Part VII: The 



Electronics 



Written By: Sean Michael Ragan 



TOOLS: 



Hex/ Allen wrench (1) 
Side cutters (1) 

Small Flathead Screwdriver (1) 
Wire stripper/crimper (1) 



PARTS: 



• Mounting plate (1) 
for electronics 

• Arduino shield (1) 

supplied with preset stepper drivers 

Arduino microcontroller (1) 
supplied with pre-loaded firmware 

• Bolt (2) 

for attaching mounting plate to frame 

• Cable ties (3) 

* *~ 

• Power supply (1) 
larger of the two supplied 

• Power supply (1) 
smaller of the two supplied 



© Make Projects 



www.makeprojects.com 



Page 1 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



SUMMARY 



This is the seventh of eight guides in a series documenting my build of MakerGear's Mosaic 
desktop FDM/FFF 3D printer kit. 

the frame . the Y-axis. the X-axis , the Z-axis.the extruder . the build platform. the electronics, and the first print . 

This part covers installation and wiring of the electronics that control the printer. First, the 
Arduino and attached RAMP shield are mounted on the printer frame. Second, connections 
from the build platform wiring harness, the extruder wiring harness, and other components 
are clipped to the PCB. Finally, the power supplies are connected, and formal assembly of 
the printer is complete. 



Step 1 — Tie PCBs to mounting plate 






& 



• Your Mosaic kit will probably arrive with the RAMP shield pre-installed on the 
Arduino Mega. If not, however, install the shield before proceeding. 

• Align the three small slits in the plywood mounting plate with the mounting holes in the 
RAMPS and/or Mega PCBs, as shown, 

• Pass each of three cable ties through one of the slits in the mounting plate, through the 
corresponding mounting hole in the lower PCB (the Arduino), and, finally, through the 
corresponding mounting hole (if present) in the RAMP shield. 

• Cinch down the cable ties gently, but firmly, and cut off the extra from each tie with a pair 
of side-cutting pliers. 



© Make Projects 



www.makeprojects.com 



Page 2 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Step 2 — Attach mounting plate to frame 




• Use a 2.5mm hex wrench to remove two M3x10mm socket cap bolts from the printer 
frame, as shown in the photo. Remove the washer from each screw. The screws 
themselves should be preserved as spare parts, but will not be needed again in the 
assembly of the printer. 

• Run each of two M3x14mm socket cap bolts through one of the washers you just removed, 
then through one of the round holes at either end of the electronics mounting plate, and 
finally into the corresponding captive nuts behind frame section I. Turn them down with the 
2.5mm hex wrench, but be careful, as always, not to overtighten. 

• Locate the platform heater power leads in the build platform wiring harness. Separate the 
leads for about two inches from the cut end, and strip about 1/4" of the insulation from 
each. 



© Make Projects 



www.makeprojects.com 



Page 3 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Step 3 — Build platform connections 




& 



• When making connections to the PCBs, it will be very helpful to refer to the 
diagrams in the PDF attached to this project. 

• Loosen the screw in each of two terminals D8 in the terminal block in the upper left corner 
of the RAMPS PCB, as pictured. Insert each of the two build platform heater power leads 
you just stripped into one of these terminals. The heater is not polarized, so it does not 
matter which of the two wires goes into which of the two terminals D8. Tighten the screws 
back down to secure the leads. 

• Find the 1x4 socket Y-axis stepper motor cable connector, and plug it into the center 1x4 
pin header block, as shown. The connector can be reversed later, if it turns out the Y-axis 
motor is turning the wrong way. For now, make an arbitrary choice. 

• Connect the 2-socket build platform temperature sensor to the center two pins of the 1x6 
pin header block immediately above the Z-axis stepper motor connector on the center-right 
edge of the board, as pictured. 



© Make Projects 



www.makeprojects.com 



Page 4 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Step 4 — Z- and X-axis connections 






• Locate the 1x3 socket connector from the Z-axis upper limit switch, and install it in the 3x6 
pin header block in the second position from the right, as shown. 

• Find the 1x4 socket Z-axis stepper motor cable connector, and plug it into the 1x4 pin 
header block immediately to the right of the Y-axis stepper connection. This connector can 
be reversed later, if it turns out the motor is turning the wrong way. 

• Find the 1x4 socket X-axis stepper motor cable connector, and plug it into the 1x4 pin 
header immediately to the left of the Y-axis stepper connection. Again, the orientation of 
the connector is arbitrary. 



© Make Projects 



www.makeprojects.com 



Page 5 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Step 5 — Extruder connections 






• Find the 1x4 socket connector from the extruder motor in the extruder wiring harness and 
connect it to the 1x4 pin header about center on the top edge of the PCB, as shown. As 
with the other three motors, this connection is simply flipped over later if the extruder turns 
out to be wired backwards. 

• Find the 2-pin connector from the hot end fan in the extruder wiring harness and connect it 
to the two leftmost positions in the upper 1x6 socket header. The red wire goes to the left, 
as shown. 

• Find the 2-socket connector from the temperature sensor in the extruder wiring harness 
and connect it to the two leftmost positions in the 1x6 pin header, center right edge, 
immediately to the left of the build platform temperature sensor connector. 



© Make Projects 



www.makeprojects.com 



Page 6 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 



Step 6 — Power connections 






• Loosen the screw in each of two terminals D10 in the terminal block in the upper left 
corner, as pictured, of the RAMPS PCB. Insert one of the two extruder heater power leads 
into each of these terminals. One of these wires is green, and one is white, but the heater 
is not polarized, so it does not matter which of the two wires goes into which of the two 
terminals D10. Tighten the screws back down to secure the leads. 

• Connect the 20V power supply in the top two positions of the 4-position Molex terminal 
block in the lower left corner of the PCB, as shown. The connector on the power supply 
cord should be clearly marked on one side with a large + symbol. Be sure to orient the 
connector with the + in the upper position, as shown. Reversing this connection can 
destroy the electronics and may present a fire hazard. 

• Connect the 12V power supply in the bottom two positions of the 4-position Molex terminal 
block in the lower left corner of the PCB, as shown. The connector on the power supply 
cord should be clearly marked on one side with a large + symbol. Be sure to orient the 
connector with the + in the upper position, as shown. Reversing this connection can 
destroy the electronics and may present a fire hazard. 

When you're done making the connections to the PCB, you may have quite a messy bowl of 
spaghetti hanging off the side of your printer. Make sure that the wires are clear of the moving 
parts of the robot, but resist the temptation to start tidying up with zip ties and cable clips until 
you've got the printer calibrated and running more-or-less as you like it. Adjustments during 
setup may require partial dismantling of the printer, including removing the PCB and side panel, 
and you'll want to save any straightening up until you're fairly confident you won't have to undo it 
for awhile. 



This concludes formal assembly of the Mosaic. There's still a lot to do to get it up and running, 
and the details of how to do that will vary with the details of the computer and software you use. 

© Make Projects www.makeprojects.com Page 7 of 8 



The MakerGear Mosaic 3D Printer - Part VII: The Electronics 

When I get mine printing, I will post a description of the process and link it from this guide. In the 
meantime, Marcus Dobeck and Rick Pollack have prepared a Getting Started PDF that should 
get you well on your way. 

This document was last generated on 201 2-1 1-011 2:45:39 AM. 



© Make Projects www.makeprojects.com Page 8 of 8